| 1 |
Internal Combustion Engine Lab |
- Two Stroke Single-Cylinder petrol engine test rig with D.C. Generator
- V.C.R. 4-Stroke Single Cylinder Petrol with Eddy current Dynamometer
- 4 Stroke Diesel Engine with Rope Brake
- 4 Stroke Multi Cylinder Petrol Engine
- 2 Stroke Petrol Port Timing
- 4 Stroke Diesel Valve Timing Diagram Equipment
- Carburetors Solex
- Maruti-800 Engine
- Fuel Supply System of Petrol Engine
- Fuel Supply System of Diesel Engine
- Cut Section Model of Fuel Injector
- Diesel Injector In Cut Section
|
| 2 |
Heat and Mass Transfer Lab |
- Thermal Conductivity of Insulating Powder Apparatus
- Thermal Conductivity of Metal Bar Apparatus
- Heat Transfer in pin Fin Apparatus
- Emissivity Apparatus
- Stefan Boltzmann Apparatus
- Drop wise film condensation Apparatus
- Preference of different Heat pipe Apparatus
- Heat Transfer coefficient of forced convection Apparatus
- Heat Transfer through composite wall Apparatus
- Heat transfer through lagged Pipe Apparatus
- Unsteady state heat transfer Apparatus
|
| 3 |
Dynamics of Machine Lab |
- Scientific Make Universal Vibration Apparatus
- Scientific Make Whirling of Shafts Apparatus
- Scientific Make Static and Dynamic Balancing Apparatus
- Scientific Make Gyroscope Apparatus
- Scientific Make Universal Governor Apparatus Watt porter, Proell, Hartnell Governor
- Tachometer
|
| 4 |
Engineering Thermodynamics Lab |
- Cornish boiler model – 10111
- Boiler model 10114
- Lancashire boiler model – 10110
- Babcock & Wilcox boiler model - 10112
- Reducing valve model – 10150
- Expansion steam trap model – 10155
- Steam injector model-10145
- Green Economiser model- 10160
- Sudgen super heater model- 10161
- Steam engine D slide valve model-10170
- Spring loaded Safety valve model – 10132
- Stop valve Hopkinson type model-10139
- Blow off cock model 10148
- Feed check valve model-10140
- Lever Safety valve model – 10133
- Dead weight Safety valve model -10133
- Pressure gauge model - 10146
- Fusible plug – 10151
- Combined high steam & low water valve model -10134
- Anti priming pipe model -10152
- Model of 2 Stroke petrol engine model-10211
- Model of 4 stroke petrol engine model -10212
|
| 5 |
Refrigeration & Air-Conditioning Lab |
- Cooling Tower Test Rig
- Simple Absorption System Test Rig
- Refrigerator Tutor Test Rig
- Air Conditioning Test Rig
- Mechanical Heat Pump
- Vortex Tube Refrigeration
- Domestic Refrigeration Test Rig
- Air Water Heat Pump
|
| 6 |
Robotics Lab |
- Sensor Scanning System
- Servo Motion Setup
- IR Proximity Sensor
- Ultrasonic Range Finder
- 5-Axis Industrial Manipulator
- Wooden Models
|
| 7 |
Mechanical Measurement and Metrology Lab |
- Vernier Caliper 150 Mm/6”
- Vernier Caliper 300 Mm/12”
- Vernier Height Gauge 300mm/12”
- Depth Micrometer 0-25 Mm
- Set Of Slip Gauges 83 Pcs
- Bevel Protector – 150 Mm
- Sine Bar- 200 Mm
- Combination Set 300 Mm/12”
- Optical Flats 50 Mm
- Surface Plates 24” X 24”
- Dial Indicators
- Snap And Ring Gauges (Go And No-Go Type All) (Total 6 Pcs)
- Strain Measurement Module
- Potentiometer
- LVDT Module
- Static Pressure Sensor Module
- Temperature Measurement Module (RTD, Thermistor, Thermocouple)
- Rotameter
- Dead weight pressure gauge Tester
|
| 8 |
Material Testing Lab |
- Impact Testing Machine (Izod & Charpy)
- Fatigue Testing Machine
- Torsion Testing Machine Model No. T.T.10
- Erichsen Cupping Testing Machine
- Rockwell Cum Brinell Hardness Testing Rab -250
- Spring Testing Machine Cap 2000 Kg.
- Super Fine Universal Testing Machine Electronics UTM 60 Ton.
- Electronics Extensometer
|
| 9 |
Fluid Mechanics Lab |
- Apparatus for Determination of Metacentric height
- Verification of Bernoullis Theorem
- Impact of jet Apparatus
- Flow Measurement by Veturimeter
- Loss in pipe friction Apparatus
- Flow Through orifice & Mouth piece Apparatus
- Reynolds Apparatus
- Complete setup for flow measurement using pitot Tube
|
| 10 |
Workshop |
- Heavy Duty Bench Grinder M/c (0.25 H.P.)
- Bench Vice
- Centre Punch G Type
- Carpentry Try Square Small Blade 6"
- Claw Hammer With Handle 1/2 L.B.
- Hira Carpentry Vice Unbreakable 8"
- Cotton Tape 30 Mtr.
- Cylinder Key
- Chipping Hammer
- Cable
- 25 mm Cap Pillar Drill M/C With Fine Feed & Electrical M/C
- Drill Chuck 1/2"
- Firemer Chisel With Handle 1/2"
- Flat File 10" 2nd Cut
- Flat Wood Rasp Cut File 10"
- Hammer Drop Forged With Handle 500 GM
- Hexa Frame Fix Heavy 3/16"
- Parket Hand Shearing Machine
- H/R File Smooth 10"
- Hand Saw Plastic 12"
- Hose Pipe
- Iron Jack Plank with Blade 14"
- Jenny Caliper Type 6"
- Knife Edge File 6"
- Prabhat Make 4' 6" Senior Model Lathe M/C With Standard Accessories
- Suraj Make Universal Gear Head M/C Milling 5Mtr 2'
- Electrical Motor 2 H.P. Coolant Pump Switch V-Belt
- Dividing Head
- Milling Vice
- Micro Meter
- Mortise Chisel With Handle 1/2"
- Creative Make Semi Hydraulic Casting Body Power Hacksaw M/C
- Plastic Mallet Hammer 40 mm
- Plier 8" Vikny
- Parting Tool
- Screw Driver
- Round File 10" Bastard
- Round Edge File 6"
- Regulator Oxytact
- Scale 12"
- Anoop Shaping M/C Model HD 185 With Universal Vice Electrical Motor
- Spring Caliper Inside 6"
- Spring Caliper Outside 6"
- Steel Scale Stainless steel 12"
- Sledge Hammer 1-1/2 Kg
- Square File 10" Bastard
- Square File 8" Bastard
- Steel Tape 3 Mtr
- Scriber
- Surface Plate 18'X18"
- Spirit Level
- Spark Lighter
- Swage Block 12"
- Triangle File 10" Smooth
- Tenon Saw 10"
- Triangle File 10" Bastard
- Triangle File H/R 10" Bastard
- Triangle Wood Rasp 10"
- Tool Holder 3/8"
- Tool Holder 1/2"
- Vernier Caliper 150 mm
- Vernier Caliper 300 mm
- Wooden Jack Plane 14"
- Welding Torch
- White Glass
- Welding Holder
- Trowels 6"
- Trowels 5"
- Tray 20'X16'X2 "
|
| 11 |
CAD/CAM Lab |
- IBM Desktop
- HP Intel Desktop
- APC UPS 500 VA
|
| 12 |
Fluid Machines Lab |
- Pelton Turbine Test Rig -3.75 Kw
- Francis Turbine Test Rig -3.75 Kw
- Variable Speed Centrifugal Pump Test Rig
- Reciprocating Pump Test Rig
- Kaplan Turbine Test Rig 1 KW
|